What is Platform Scales?

A weighing scale ("scale" in common usage) is a device for measuring weight, often of a person. Balances measure the mass of an object and are used in science to obtain the mass of an object. In many industrial and commercial applications, scales and balances to determine the weight and/or mass of things ranging from feathers to loaded tractor-trailers.

Occasionally, an appropriate weighing scale may be used to measure force rather than mass.

Balances

This electronic balance is used to measure mass in a school laboratory.

A balance (also balance scale, beam balance, or laboratory balance) is used to measure the mass of an object. In its conventional form, this class of measuring instrument compares the sample, placed in a weighing pan (weighing basin) and suspended from one end of a beam with a standard mass (known mass) or combination of standard masses in a scale pan (scale basin) suspended from the other end. To weigh an object in the measuring pan, standard weights are added to the scale pan until the beam is in equilibrium. Then, a slider weight—usually present—is moved along a scale on or parallel to the beam (and attached to it) until fine balance is achieved. The slider position gives a fine correction to the mass value.

When the weights on the plates of this balance are equal, the needle mid-rod points straight up.

Very precise measurements are achieved by ensuring that the fulcrum of the beam is friction-free (a knife edge is the traditional solution), by attaching a pointer to the beam which amplifies any deviation from a balance position; and finally by using the lever principle, which allows fractional weights to be applied by movement of a small weight along the measuring arm of the beam, as described above. For greatest accuracy, there needs to be an allowance for the buoyancy in air, which effect depends on the densities of the weights and the sample.

While the word "weigh" or "weight" is often used, any balance scale measures mass, which is independent of the force of gravity. The moments of force on either side balance, and the acceleration of gravity on each side cancels out, so a change in the strength of the local gravitational field will not change the measured weight. Mass is properly measured in grams, kilograms, pounds, ounces, or slugs.

The original form of a weighing scale consisted of a beam with a fulcrum at its center. For highest accuracy, the fulcrum would consist of a sharp V-shaped pivot seated in a shallower V-shaped bearing. To determine the mass of the object, a combination of reference weights was hung on one end of the beam while the object of unknown mass was hung on the other end. For high precision work, the center beam balance is still one of the most accurate technologies available, and is commonly used for calibrating test weights.

To reduce the need for large reference weights, an off-center beam can be used. A scale with an off-center beam can be almost as accurate as a scale with a center beam, but the off-center beam requires special reference weights and cannot be intrinsically checked for accuracy by simply swapping the contents of the pans as a center-beam balance can. To reduce the need for small graduated reference weights, a sliding weight, called a poise, can be installed so that it can be positioned along a calibrated scale. A poise adds further intricacies to the calibration procedure, since the exact mass of the poise must be adjusted to the exact lever ratio of the beam.

For greater convenience in placing large and awkward loads, a platform can be "floated" on a cantilever beam system which brings the proportional force to a "noseiron" bearing; this pulls on a "stilyard rod" to transmit the reduced force to a conveniently sized beam. This design can still be seen in "portable beam scales" of 1000 lb or 500 kg capacity which are commonly used in harsh environments where electricity is not available, as well as in the lighter duty mechanical bathroom scale. The additional pivots and bearings all reduce the accuracy and complicate calibration; the float system must be corrected for corner errors before span is corrected by adjusting the balance beam and poise. Such systems are typically accurate to at best 1/10,000 of their capacity, unless they are expensively engineered.

Some expensive mechanical scales also use dials with counterbalancing weights instead of springs, a hybrid design with some of the accuracy advantages of the poise and beam but the convenience of a dial reading. These designs are expensive to produce and are largely obsolete thanks to electronics.